LED Wall Washer 18W Sleeve Design Onsite Maintenance

LED Wall Washer 18W Sleeve Design Onsite Maintenance

Short Description:

LED wall washer with Sleeve Core® design is an innovative and future-proof product that, for the 1st time, allow site maintenance in hard-to-reach locations, The core part can be renewed with little effort while keeping the original bracket.

 

Constant voltage+Constant current driving mode with integrated IC driver on board, high working reliability in a small format.


  • Input : DC24V
  • Rated Power: 18W
  • Product Dimensions: 1000*31*38mm
  • LED Type: CREE/LumiLEDs 3030
  • Materials : 6063 Aluminum alloy, 4mm Tempered glass
  • Product Details

    Download

    Application

    Video

    Tags

    Features

    • Unique Sleeve Core® design, improve the waterproofness to a new level while allowing site replacement
    •  Separated current-go-through wiring, allow continous connection of up to 20pcs 100cm wall washers without visible brightness/voltage reduction
    • Venting respirator applied on all models, prevent condensation in low-temperature environment or big temperature shifts
    • Special junction box, avoid possible pull out of wires during installation
    • Top quality silica gel with good elasticity, avoid failure of LEDs(gold wire) under expansion by heat and contraction by cold
    • Individual PMMA lens on each LED, avoid color shift to provide light with high color consistency and uniformity

     

    Benefits

    • Reduced maintenance cost by only replacing the core part, ideal for EMC(energy management contract) project
    • Reliable and long-lasting performance even in extremely low-temperature environment
    • No visible brightness reduction for long continous connection, easy to install and reduced labor cost
    • Future-proof product

     

    General Data

    Model 

    Dimensions (L*W*H)

    Rated Power

    Luminous Efficacy*

    Luminous Flux* 

    CCT/Color

    LED Type

    Beam Angle

    Input 

    DT-WS-100-18-A

    1000*31*38mm

    18W

    90lm/W

    1620lm

    2400K

    3000K

    R/G/B/RGB

    SMD3030

    30°/45°/60°/ 10*65°…

    DC24V

    * Tested data at 3000K with clear glass cover, tolerance ±5%

     

    Additional Characteristics

    Mechanical

    Materials

    6063 Aluminum alloy, 4mm Tempered glass

    LED Brand

    CREE/LUMILEDS

    Bracket Adjustable Angle

    180˚

    Electrical

    Driving Mode

    Constant voltage+Constant current

    Control Mode

    ON/OFF/DMX512

    Electrical Safety Class

    Driver Type

    On-Board IC

    Driver Protections

    Short circuit, Over current, Over voltage, Over temperature

    Optical

    Beam Angle

    8°/25°/30°/45°/60°/ 20*45°/10*60°/10*65°

    SDCM

    <4

    UGR

    <25

    Operating Conditions&Lifespan

    Ingress Protection

    IP65

    Ambient Temperature

    -30˚C ~ 50˚C

    Storage Temperature

    -40˚C ~ 80˚C

    Switching Circles

    100,000

    Lifespan(L70B50)

    50,000h

    Standard Warranty

    5 Years

     

    Light Distribution 

    LED wall washer beam angle and light distribution

     

     

    LED wall washer beam angle and lighting height

     

     

    Product Drawing(±1mm)

    LED Wall Washer drawing

     

     


  • Previous:
  • Next:

    Installation Guidance

    LED Wall Washer installation drawing

    LED wall washer wiring scheme

    LED wall washer connection method

    NOTICE:

    1) Computer/master and second-control, second-control and differential receiving card are connected by pure copper twisted pair cable for data transmission. Differential receiving card and LED wall washer, and LED wall washers themselves are connected by the male and female waterproof connector.

    2) Cable length between the computer/master and second-control, second-control and differential receiving card cannot exceed 100 meters, the switch or extended fibre-optical is necessary if exceeded. Distance between the differential receiving card and wall washer cannot exceed 5 meters, if exceeded, the signal amplifier is required to amplify and shape the signal.

    3) Combined current of wall washers connected in each branch cannot exceed the rated over load of power supply

    4)The combined wattage of wall washers in each branch cannot exceed 80% of the power supply

     

    Project Photos

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Flag

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Key